How the estimate works
Measure the clear space
Hold your tape between the faces of the posts at the plane where the pickets will sit. Do not use the distance from one post center to the next: a nominal 8 ft bay has less than 96 in of clear width once the posts occupy part of that distance. Check several locations before treating bays as identical. A slight change near the width of one board can change the count.
Measure actual board width
Use the face width of the board, not the nominal lumber name. Lay out a few boards side by side from the batch when you can. For a gap layout, the repeated module is one board plus the gap to the next board. For solid side-by-side pickets, set the gap to zero. Alternating or overlapping board layouts need their own takeoff because the visible face coverage differs.
Find whole boards per bay
For n pickets of width w and a gap g, the occupied distance is n × w + (n − 1) × g. Rearrange to n ≤ (clear width + g) ÷ (w + g) and round down. There are only n − 1 gaps because there is no gap after the final board in this calculation. Subtract the occupied distance from the bay width to see how much space remains.
Turn the layout into a purchase quantity
Multiply whole pickets per bay by the number of equal bays. For different bay widths, run separate estimates and combine the underlying counts before applying one overall allowance. The final purchase count rounds up. If boards are sold in bundles, divide the purchase count by boards per bundle and round up again at that packaging step.
Worked example
A clear bay of 92.5 in takes 5.5 in wide boards with a 0.25 in gap. Divide 92.75 by 5.75 to get about 16.13, so 16 boards fit. They occupy 16 × 5.5 + 15 × 0.25 = 91.75 in. The remaining 0.75 in could be split into two 0.375 in end margins. Six identical bays call for 96 boards. A 10% allowance gives 105.6, so round up to 106 boards.
- Clear bay width (in)
- 92.5
- Identical bays
- 6
- Picket width (in)
- 5.5
- Gap between pickets (in)
- 0.25
- Extra material (%)
- 10
Reference table
| Gap (in) | Pickets per bay | Pickets to buy |
|---|---|---|
| 0 | 16 | 106 |
| 0.25 | 16 | 106 |
| 0.5 | 15 | 99 |
| 1 | 14 | 93 |
Common mistakes
- Counting a gap after every board. There is one fewer interior gap than pickets. If you want equal gaps at both ends too, deduct those two end spaces from the clear width first.
- Rounding up boards inside a bay. Rounding up before checking fit assigns space your bay does not have. Round down for the layout and up only for the order allowance.
- Combining unlike bays. Partial space at the end of one bay does not carry over through the next post. Calculate each repeated bay size separately.
How much extra should I buy?
For consistent stock and a simple pattern, 5–10% extra is a reasonable starting allowance. Consider 10–15% when you expect to reject warped boards or rip several boards to match narrow returns. Longer runs are a good reason to group measurements by bay width rather than to inflate the allowance across the board. For a short run, percentage math can leave only one spare. Decide whether to buy another board based on how easily you can get a matching replacement later.
Before you order
Write a bay schedule before ordering. Note each clear opening, whether the fence follows a slope, and which bay receives an end board that will be ripped narrower. Mark bays with the same usable width so you can enter them together. For a stepped run, the vertical change does not affect the width calculation, but it can change the height of the pickets you need. Record heights separately from quantities. If a panel follows a slope, check the actual installed spacing at the line where you will fasten the boards.
Lay out one representative bay with a spacer and the actual pickets before buying the full quantity. Measure the combined width of several boards and compare it with the calculator’s assumed coverage. If the stock varies, use a representative measured width and keep installation clearances flexible where the design permits. Bring the bay schedule to the supplier, particularly if pickets come in mixed packs or if the gate uses a different profile. A total board count is a purchasing quantity; the bay schedule tells you where each batch goes.
If you are also buying posts and rails, build a full straight-run fence materials list. For a fence with separate hole sizes, estimate concrete and gravel by post group.
Sources and assumptions
- Coverage comes from the measured board face, one gap between adjacent boards and the clear width of each bay.
- Inspect the actual stock and supplier bundle size before ordering, especially for nominal or overlapping boards.
Choose a spacing for the fence style
A single-layer privacy layout uses a small or zero planned gap, while an open picket design leaves more space between boards. Measure actual stock from the lot. If the design calls for overlap or alternating faces, calculate each layer independently because the repeating module is different.
Keep the end margins consistent
Dry-lay one bay and compare its leftover space with the desired margin around the posts. Equal end margins can keep adjoining bays looking consistent. If the margin is larger than expected, check if one more board fits before changing the planned gap. Record any ripped end boards on the cutting list.
Another project to check
A 67 in clear bay uses 3.5 in pickets and a 0.5 in gap. Repeat the bay four times and include 5% extra stock.
- Pickets per bay
- 16
- Pickets before allowance
- 64
- Pickets to buy
- 68
Frequently asked questions
How many pickets fit in an 8-foot fence section?
It depends on the actual opening between posts, picket width, and gap. For a 92.5 in clear opening with 5.5 in boards and ¼ in gaps, 16 pickets fit.
Can I use this for a privacy fence?
Yes, use a zero gap for a single layer of edge-to-edge boards. Board-on-board and shadowbox patterns need a calculation for each layer or alternating face.
What do I do with the space left over?
You can center the layout by dividing the leftover width between the two ends. Another option is adjusting the gap uniformly if your design allows it.
Are gate pickets included?
Only if you enter the clear width and count of gate panels as a separate set of bays. Keep gate measurements separate from fixed fence bays.
This is a material estimate. Verify measurements, product coverage, and applicable local requirements before buying or building.