How the estimate works
Measure the straight run
Enter the planned length along the finished face of the wall, in feet. If a project has multiple straight sections, record them separately, particularly near corners, steps, and returns. The calculator covers a single straight run with uniform height. It does not count special corner units or assume that cut pieces can be reused on a second run. Those quantities belong on a product-specific cut list.
Determine blocks per course
Convert the run length to inches, divide by the installed face length of a block, and round up. Use the width the block contributes in the installed pattern. Its maximum overall dimension or nominal package name can differ. Each course is counted separately, so the final whole block in one course does not provide material to the next course in this estimate.
Determine the course count
Divide the visible block height by the installed rise per course and round up. Add the specified number of fully buried courses. Use the height to the top of the block courses, excluding a distinct cap layer. If an approved plan uses a partially buried course or a stepped base, group heights by section and adjust the counts to match that plan. This calculator does not determine embedment or wall geometry.
Order block and cap pieces separately
Multiply blocks per course by the total number of courses. Caps form one row and may have a different installed length than the blocks. Divide wall length by cap length and round up. Apply the allowance independently to each material and round to whole pieces. If units are only sold by layer or pallet, convert each purchase amount to the supplier’s packing increment.
Worked example
A 24 ft wall is 288 in long. With installed 12 in face blocks, each course needs 288 ÷ 12 = 24 blocks. The visible block height of 24 in divided by the 6 in rise is four exposed courses. Add one buried course for five total. That gives 120 blocks before allowance. Add 10% for 132 blocks. At 12 in per cap, the top row takes 24 caps. A 10% allowance raises the order to 27 caps.
- Wall length (ft)
- 24
- Visible wall height (in)
- 24
- Installed block face length (in)
- 12
- Installed block course height (in)
- 6
- Additional buried courses
- 1
- Installed cap length (in)
- 12
- Extra material (%)
- 10
Reference table
| Visible block height (in) | Total block courses | Wall blocks to buy | Caps to buy |
|---|---|---|---|
| 12 | 3 | 80 | 27 |
| 18 | 4 | 106 | 27 |
| 24 | 5 | 132 | 27 |
| 30 | 6 | 159 | 27 |
Common mistakes
- Omitting buried courses. Use the count specified in your design. A fully buried course still runs the length of the wall and needs blocks.
- Including caps in visible block height. If your overall height includes a separate cap, subtract the cap thickness before calculating block courses.
- Using the count to design the wall. Block quantity does not determine base, drainage, reinforcement, or permitting. Confirm those requirements separately.
How much extra should I buy?
For a simple straight run using consistent stock, 5–10% is a practical planning range for cuts and breakage. A stepped wall with returns or patterned courses can need more, including separate corner or end pieces. Track cap cuts independently since caps have their own geometry. Check exactly which units the supplier sells individually before rounding to a pallet.
Before you order
Make a course-by-course sketch showing changes in elevation, where cuts land, and which ends are exposed. If the entire run is level and straight, each course will often have the same number of blocks, but the actual order can change if the installation pattern alternates end pieces. Check whether your selected product uses left and right corners, tapered faces, or a multi-size pattern sold in a fixed ratio. Count special pieces separately before deciding how many standard units to buy.
Record the block dimensions as installed. The visible face of a unit and the overall body of the unit may have different dimensions. The product guide can explain the coverage contributed by an individual piece or a matched set. For caps, consider whether the catalog lists coverage by linear foot or by part count, and whether mitered pieces or end returns require additional stock.
Ask the supplier to confirm the ordering increment. If a pallet contains 96 blocks, the example quantity of 132 would require two full pallets when partial units are unavailable. That purchasing surplus is separate from the ten percent material allowance. Keep drainage stone and leveling-base aggregates on a separate volume takeoff. Confirm that your measured quantities reflect the project plan before ordering materials.
Use the bulk gravel volume and weight calculator for separately specified aggregate. For a patio next to the wall, estimate pavers, base, bedding, and edging independently.
Sources and assumptions
- Counts use installed block and cap face lengths, installed rise per course, and buried courses from your plan.
- Verify product coverage, special units and packing increments. The count does not establish a safe wall height or reinforcement design.
Height rules and reinforcement come from the design
There is no universal wall height at which every project needs engineering or permits. Check local requirements and the chosen wall system, including the effect of slopes, nearby loads, and buried height. If the approved design specifies geogrid or reinforcement, take those quantities from the design separately.
Plan drainage and cap pieces as separate orders
Estimate drainage aggregate and a leveling base from their specified dimensions. They are not included in the block count. Caps use their own installed length, and visible ends may call for different pieces or cuts. Check which special units the supplier stocks before rounding the order up to packages.
Another project to check
A straight 17 ft run has 21 in of visible block height. The selected units have a 14 in installed face, 7 in course rise, and 16 in caps. Include one buried course and 8% extra.
- Total block courses
- 4
- Blocks per course
- 15
- Wall blocks to buy
- 65
- Caps to buy
- 15
Frequently asked questions
How many blocks are in one retaining wall course?
Divide the run length by the installed face length in the same unit and round up. A 288 in run takes 24 blocks of 12 in each.
Do retaining wall caps count as another block course?
No. Calculate cap pieces separately and exclude a separate cap layer from the visible block height you enter.
Can I use this calculator for a curved wall?
This estimate is for straight runs. Curves may use different effective face dimensions and more cuts, so work from the product layout.
Does this calculate how deep to bury the first course?
No. Enter the additional buried courses from your design. Verify construction and permitting requirements before starting.
Does the count include geogrid or drainage gravel?
No. Use the design to estimate reinforcement, and take off drainage gravel separately using the specified layer dimensions.
This is a material estimate. Verify measurements, product coverage, and applicable local requirements before buying or building.