How the estimate works
Measure the finished footprint
Multiply length × width in feet to get square feet. Use inside form dimensions. If the slab has a step or a cutout, split the shape into rectangles and subtract any area that will remain empty. Keep areas of different thickness separate so that a thin walkway is not estimated at the thicker slab depth.
Convert thickness to feet
Divide thickness in inches by 12 before multiplying by square footage. This yields cubic feet. Four inches is one third of a foot; using 4 directly would enlarge your result twelvefold. For a uniform slab, a 10% increase in depth increases required volume by 10% when length and width stay fixed.
Account for thicker edges separately
The calculator assumes uniform thickness. If a portion is thicker, calculate its extra depth beyond the main slab, multiply by the affected area, and add that extra volume. A thickened edge can overlap at corners if estimated as independent strips. Subtract overlap or measure a nonoverlapping outline. Neither base gravel nor reinforcement is included in the concrete volume.
Convert to an order quantity
Multiply cubic feet by one plus the allowance as a decimal. Divide by 27 for cubic yards, or divide by cubic feet per bag and round up. Keep the full calculated volume through the conversion; a display rounded to two or three decimals is for reading, not the input to the bag calculation. Ask a ready-mix supplier about its minimums and increments.
Worked example
A 12 ft by 10 ft slab at 4 in thickness covers 120 ft². Multiply that by 4 ÷ 12 to get 40 ft³. With 10% extra, the order quantity is 44 ft³, equivalent to 44 ÷ 27 = 1.630 yd³. If an 80 lb bag yields 0.60 ft³, divide 44 by 0.60 to get about 73.33, then round up to 74 bags.
- Length (ft)
- 12
- Width (ft)
- 10
- Slab thickness (in)
- 4
- Yield per bag (ft³)
- 0.6
- Extra material (%)
- 10
Reference table
| Slab thickness (in) | Concrete to order | 40 lb bags | 60 lb bags | 80 lb bags |
|---|---|---|---|---|
| 3 | 1.222 yd³ | 110 | 74 | 55 |
| 4 | 1.63 yd³ | 147 | 98 | 74 |
| 5 | 2.037 yd³ | 184 | 123 | 92 |
| 6 | 2.444 yd³ | 220 | 147 | 110 |
Common mistakes
- Mixing square and cubic units. Square feet measure surface coverage. Concrete is sold by volume, so the slab’s thickness is needed.
- Using a bag’s dry weight as its volume. Pounds describe the package weight. The product’s published mixed yield is the right divisor for bag count.
- Estimating from the deepest point alone. For distinct slab zones, compute each zone separately. Direct measurements of the prepared form are better than guessing an average.
How much extra should I buy?
For measured forms on a reasonably even base, 5–10% extra is a practical planning range. More irregular excavations may call for their own volume estimate instead of a larger blanket percentage. Check depth at several locations and include measurable low spots. When a truck order must be rounded to a supplier increment, compare that increment against your calculated allowance so you know how much concrete you are actually ordering.
Before you order
Write the measured volume and the requested order amount separately. A supplier may accept quarter-yard or other increments, and the final truck amount can differ from the unrounded estimate. For bagged mix, compare the data sheet for the 40, 60, or 80 lb product you can actually buy. The table uses example yields of 0.30, 0.45, and 0.60 ft³. A different formulation or package can produce a different volume per bag, even when two bags have the same weight.
If the pour consists of several pads, make one line per pad with its footprint and thickness. Add the unrounded quantities for pads poured together. For separate batches, decide whether leftovers can be shared before relying on one combined bag count. When your supplier quotes ready-mix by the yard, send it both the calculated quantity and the planned allowance so any quote can be checked against your takeoff.
Before placing an order, remeasure the inside edges of the forms and confirm the actual effective depth over the prepared base. Check corners and transitions as well as the center. Moving a form or adding a thickened edge can change the result after the first estimate. Update the dimensions directly whenever you know those changes instead of assuming an earlier estimate still applies.
Keep the final takeoff with the form measurements so another person can reproduce the order quantity.
Estimate the subbase separately with the gravel volume and weight calculator. If the project uses modular units instead of a pour, check the paver patio and base calculator. If you already know the total volume, compare 40, 60, and 80 lb concrete bag counts.
Sources and assumptions
- The slab has a rectangular footprint and uniform thickness. The model converts inches to feet and 27 ft³ to one yd³.
- Bag comparisons use the example yields shown in the QUIKRETE Concrete Mix technical sheet. Check the actual product and the ready-mix supplier’s order increments.
Measure form depth at low spots
Check the distance from the top of the planned pour to the prepared base at several points. Estimate a distinct depression from its footprint and additional depth. Where a thickened edge overlaps another thickened strip at a corner, count the overlapping volume only once.
Compare a bulk quote with the bag result
Keep your adjusted cubic-yard quantity separate from the supplier’s rounded delivery quantity. For bagged mix, compare mixed yield and dry package weight separately. If you already know the volume, the bag calculator can compare alternate products without re-entering the slab geometry.
Another project to check
An 18 × 5 ft walkway is modeled as a uniform 3½ in slab. Enter the measured depth, add 8% extra, and use the 60 lb bag’s example yield.
- Concrete bags
- 63
- Concrete before allowance
- 26.25 ft³
- Concrete to order
- 1.05 yd³
Frequently asked questions
How many cubic yards do I need for a 10 by 12 slab?
At 4 in thick, the slab uses about 1.481 yd³ before allowance, or 1.630 yd³ with 10% extra.
How many 80 lb bags make a yard?
At 0.60 ft³ per bag, 27 ÷ 0.60 equals 45 bags before allowance. Use the yield on your bag because mixes vary.
Does this include a gravel base?
No. The volume refers to concrete only. Measure the gravel layer separately using its own depth.
Can I use this to choose slab thickness?
The calculator estimates a supplied thickness. Confirm design, site requirements, and local rules before deciding on slab dimensions.
How do I include a thickened edge?
Calculate the extra volume below the main slab separately, accounting for corners where edges meet. Add it to the slab volume before choosing an order quantity.
This is a material estimate. Verify measurements, product coverage, and applicable local requirements before buying or building.